![]() ![]() This is why the beauty of the engines made since the year 2000 is so nice. How To Check Engine Hours On Yamaha, Mercury, Honda, Evinrude, Suzuki Outboards! Just by going off of the hour meter on the boat. If the gauge is replaced, then all the hours are reset and it’s back to zero! So there is no way of “really” telling how many hours an engine has. Seeing that the hour meter only really reads the amount of time the key was on. The possibilities that the hours are accurate are not very high. How many times was the key switch left on at the sand bar? On the trailer, at the ramp, on the dock, while getting fuel? This can become very vague, and not very accurate though. Regardless of whether the engine is running or not! That every time the key switch is on, the hour meter is running. This voltage comes from the key switch, which means. The way that the hour meter on console operates, is that it runs from the voltage that is supplied to it. You have to rely on the hour meter that is on the console. Yes, originally, and on engines that have been manufactured before then. Have the capability of storing engine hours. 2000.00įor a 600HP big block that will idle well to prevent reversion, and be able to run hard for long periods of time.Īt least with a BBC you can find this stuff used you never can with a good small block.Almost all outboard engines that have been produced since the year 2000. Single belt Na Kit with power steering sea pump et. ![]() You need to get into some used parts AND come up with a bit more scratch.Īnyway lets add it up-real rough maybe you have some of this already maybe not-ĭecent BBC manifold exhaust system & tails 3000.00Ī low end on hydraulic single ram steering kit 1500.00 I guess i'm going BIG CUBES!!!!Cyborg tran on a bravo? Never seen that.ġ0K dont think so though not for everything you need to get want you are looking for. Thanks for the input eat videos and that seagull got his 1.5 sec of fame.holy smoke was that close! Steering will be updated to external no questions asked and will mate it to a cyborg tran.īottom line! i was tryn to get a little crazy with a SBC but N/A BBC wins everytime. My budget all said and done is about ten thousand. make huge RPM's with 600+ hp and close to matching Tq. I wanted to stick with my base 350 and build it up, but from ever person i talk to they tell me run the boat for the summer have fun with it and mean while build a big block N/a.įlip side of the coin is i have seen 427 or 434 N/a lil M dart blocks with all the goodies. Scroll around a bit on these-check out the near bird strike at 2:55 on the forward facing video. Have you thought about how you are going to steer your boat with all this newly acquired power? Better save even more for an external steering kit. ![]() If you are going to build a blower engine you need to go gut the whole thing and start from the block and crank up and spend real big money. Unless you got big money to spend chasing down air fuel ratios and building outdrives. Heres more free advice - do it NA skip all the air pushing nonsense. Get a 400 dart block or brodix as you say- at min and go up from there. Sure if you go into the block you can stroke it, but then if you are doing that why start with a 350? Youll need to splay cap it and it wont stroke big enough to get any real cubes. If you want to build up your 350 stick with heads and a top end kit for now. Id be building an engine on a stand while you enjoy your boat. Not available used for a SBC - they are like hens teeth. If this wer for a car - not so, but its not, its for a boat and you'll need expensive good parts you wont find used like the guy above says you need a real exhaust system. IF you are shooting for 600 in a a marine small block will be very expensive to get you there vs a big block and you just wont save any money. I'm in it for the long haul.As one of the few guys on this or any site with a 500+HP small block- if you are in it for the long haul go get a big block. ![]() Or should i run the boat for a season,wait till next summer and go low compression and buy the dart block and go 671 or 871 blower and have KING KONG POWER. With that said should i just buy a Dart block and go nuts N/A or will my 350 be ok to stroke up to 434 or is 383 a better idea? ![]()
0 Comments
Leave a Reply. |